Whether you purchased a Schlage Encode from a previous owner or need to reset the device for any other reason, you have found the article you were looking for! We are going to find out right now how to factory reset a Schlage Encode (even if you do not have the code.)

To factory reset a Schlage Encode, all you need to do is to press and hold the reset button on the inside of the keypad for about 10 seconds until the LED light stops flashing red. Then, wait for 10 more seconds until the light turns blue. Then enter the default code to officially restart it.  

Now, in this article, we will go through the instructions step by step to factory reset your Schlage Encode, as well as what to do if you can’t find the default programming code and a whole lot more. So keep reading. Everything you need to know is right here. 

How to Factory Reset Schlage Encode 

So, if any of these above situations applies to you, then you will certainly want to know how to factory reset your Schlage Encode. 

And luckily, it really isn’t all that challenging! You can do it yourself in just a few minutes. You don’t even need any tools; just follow these instructions:

  • Remove the back plate to expose the inside of the lock.
  • Press and hold the reset button.
  • The LED light will start flashing red.
  • Hold down the button until the light stops flashing.
  • The lock will go into reset mode (which can take up to 10 seconds.)
  • Once out of reset mode, the light will turn blue.

Now, you have successfully reset your Schlage Encode to factory settings! From here, you will have to set up the Schlage Encode again as if it were brand new. 

NOTE: Above the reset button you will see  white sticker with several lists of numbers. If you do not see this label, do not reset your Schlage Encode as you will not be able to complete the final step listed below without it. 

Why Would You Need to Factory Reset a Schlage Encode?

Before we dive into the instructions for how to factory reset your Schlage Encode smart lock, it’s important to understand why you may want or need to do so. 

First, you should know that factory reset is different from simply resetting or restarting the device. Sometimes, you may need to turn the device on and off again if it is malfunctioning, but that won’t reset it to the factory settings. 

Factory resets should be used for the following situations:

  • You are the new owner of a used Schlage Encode and want to ensure the previous owner cannot connect to the device.
  • If you plan to sell or return your Schlage Encode and need to disconnect from your personal information.
  • If for some reason you forget your PIN or cannot use the Schlage Encode, you can use the factory reset to start over.

Now, it’s also important to know that when you opt for a factory reset, all your previously saved information, PINs, and connections to your smart devices will be lost. 

Do You Need the Schlage Encode Default Code to Factory Reset?

As you probably noticed in the instructions listed above, at no time during the factory reset process do you need to enter a code. So what are the Schlage Encode default codes and why are they important? 

Well, while technically the Schlage smart lock did reset once the LED light turned blue, it is actually impossible to use until you enter one of the device’s default codes. 

The default code is a 4-digit numerical code that will get your Schlage Encode up and running again after the reset. 

And luckily, you can find both of your Schlage Encode’s default codes listed on the white sticker directly above the reset button within the lock. 

While you do absolutely need that default code if you have reset the code to factory settings, it is important that you change it to a personal passcode as soon as the lock is functioning properly. 

This is because any previous owners, or anyone smart enough to remove the back of your Schlage Encode could know the default code and use it to enter your home without your permission. 

Final Thoughts

So, now you know exactly how to factory reset your Schlage Encode! 

And as promised, you not only have all the information you need to successfully reset your Schlage Encode, but also understand why you may want or need to do so. 

Just remember: You need the default code on the white sticker located behind the black covering on your lock in order to successfully reset the Schlage Encode, so don’t start the process if you can’t find it!